S 620A:EPC - Horizontal Mitering Saw

S 620A/EPC Horizontal Mitering Saw


  • Heavy-Duty
  • Hydraulic
  • Miter Cutting
  • Horizontal
  • Metal Cutting
  • 5 H.P.
  • 1-1/4” Blade

Get More Info


Capacity: 45°
Rectangle 14-1/2” x 16-1/2”, Round 14-1/2”
Capacity: 60°
Rectangle 14” x 11-1/2”, Round 11-1/2”
Capacity: 90°
Rectangle 14-1/2” x 24”, Round 14-1/2”
Mitering
Manually positioned up to 60° Left and 45° right, equipped with degree scale.
Pass Line Height
32.625”
Blade
1-1/4” x .042” x 16’ 1”
Blade Tension
Hydraulically controlled tension (30,000 psi) provides consistent square cutting accuracy. The motion detector will shut the machine off should the blade break or stall.
Speed Range
65 - 325 SFPM infinitely variable through an inverter drive and a heavy-duty worm gear transmission. The broad speed range allows for optimum cutting of a large spectrum of materials. An electric tachometer assures accurate speed setting.
Hydraulic Down Feed
Feed rate and down pressure can be controlled independently for fast, accurate cutting. Setup is made easy through the color-coded dial allowing the operator to select the optimum setting for the type of material being cut. Both settings are made at the operator’s station.
Hydraulic Shuttle Feed
Length settings of 0 - 23.625” are accomplished with a hand-wheel and readout a digital counter. The shuttle comes to positive stops at both ends of the index, assuring cutoff length accuracy, reducing material loss. Repeatability is ± .005 per index. Up to 9 cycles are possible through the multi-index system.
Motors
Blade Drive: 5 H.P., Hydraulic Pump Motor: 1 H.P., Coolant Pump Motor: 1/8 H.P. - All motors are dual voltage, 230/460 volt, 3 ph. 60 Hz.
Piece Counter
The machine will stop the automatic cycle when a predetermined number of cuts have been reached.
Out-of-Stock Switch
The machine will shut off automatically when material is no longer present in the rear vise jaws, allowing for truly automatic operation.
Blade Guides
The combination of the roller bearing and carbide blade guides reduce heat and blade stress providing longer blade life and accuracies of ± .002 per inch of cut material.
Fast Approach
Work height is automatically set allowing the head to rise just enough to clear the work piece, reducing cycle time and allowing for faster cutting performance.
Chip Brush
Powered from the main drive shaft of the saw, the brush changes speed along with the blade to assure that chips are being removed from each gullet of the blade, improving cutting performance and blade life.
Full Stroking Hydraulic Vise Jaws
Holding the work piece on both sides of the blade reduces blade vibration, providing more accurate cuts and longer blade life. Rear Vise: The rear vise jaw floats hydraulically to accommodate crooked stock assuring straight, accurate cuts.
Work Light
Positioned directly over the work area to provide better illumination of the cutting area, the work light can be turned on and off independently from the operator’s control panel.
Roller Table
Standard equipment includes one freestanding roller table 5' 0" long to support incoming stock.
Pass Line Height
32.625"
Blade Tension
30,000 psi
Speed Range
65 - 325 SFPM
Blade Size
1-1/4” x .042” x 16’ 1”
Automatic Chip Removal
The chip auger rotating in the coolant return removes chips quickly and efficiently, freeing the operator to perform more productive operations.
Hydraulic Hold-downs
The nesting fixtures for vertical clamping are designed for high-production multiple cutting.  Vertically mounted hydraulic clamps located on each vise jaw apply downward pressure to hold multiple bar work or structural shapes.
Variable Vise Pressure
Hydraulic clamping pressure to the work holding jaws can be adjusted as required to hold solid or thin wall material...
3 Meter Dead Roller Table
Free standing either in feed or discharge.
6 Meter Dead Roller Table
Free standing either in feed or discharge.