Horizontal Post Style

NC530HSS Horizontal Post Style Saw


  • Heavy-Duty
  • High Speed
  • Hydraulic
  • Horizontal
  • Metal Cutting
  • 20 H.P.
  • 2-5/8” Blade
  • Servo Feed

Get More Info


Download Brochure and Spec Sheets

Capacity
20" x 20", 20" Round
Blade
2-5/8" x .063" x 21' 10-1/2": Uses either bi-metal or carbide tip blade.
Blade Tension
Hydraulically controlled tension provides consistent square cutting accuracy. The motion detector will shut the machine off should the blade break or stall.
Speed Range
49 - 393 SFPM infinitely variable through a servo motor and heavy-duty transmission. The broad speed range allows for optimum cutting of a large spectrum of materials.
Rigid Dual Column
Rides on lineal ways providing optimal cutting performance with industry leading cutting accuracy.
Servo Down Feed
Feed rate and down pressure can be controlled independently for fast, accurate cutting. Cutting data is stored in the machine's control and will automatically set feeds and speeds based on the material specs being cut. The down feed also will automatically adjust itself to different cutting resistance as the blade moves downward through the material.
Hydraulic Shuttle Feed
Length settings of 0 - 20" are accomplished by inputting the data into operator's touch screen control. The shuttle comes to positive stops at both ends of the index, assuring cutoff length accuracy, reducing material loss. Repeatability is ± .005 per index. The under slung shuttle features a 10' roller in feed table and multi-index system.
Motors
Blade Drive: 20 H.P., Hydraulic Pump Motor: 5 H.P., Coolant Pump Motor: 1/2 H.P.
The Operator's Control Panel
Conveniently located on the right hand side of the machine and offers touch screen data input and a self diagnostic system. It also offers full control of all the machine features such as; vise clamping, piece counter, shuttle advance & retract, hydraulic clamping of the blade guides, coolant, work light, and more. The touch screen controls provides built in cutting data for a large variety of materials which will aid in the set up of each job to be run.
Automatic Positioned Moveable Guide Arm
Will position itself next to the material providing maximum support of the blade through the entire cutting operation.
Piece Counter
The machine will stop the automatic cycle when a predetermined number of cuts have been reached.
Out-of-Stock Switch
The machine will shut off automatically when material is no longer present in the rear vise jaws, allowing for truly automatic operation.
Blade Guides
The combination roller bearing and hydraulic clamping carbide blade guides with vibration dampening unit, reduce heat and blade stress providing longer blade life and accuracies of ± .002 per inch of cut material.
Automatic Work Height with Fast Approach
Work height is automatically set allowing the head to rise just enough to clear the work piece, reducing cycle time and allowing for faster cutting performance.
Chip Brush
Powered from the main drive shaft of the saw, the brush changes speed along with the blade to assure that chips are being removed from each gullet of the blade, improving cutting performance and blade life.
Full Stroking Hydraulic Vise Jaws
The Front vise jaws are split to reduce the remnants to as little as 4.3". The split vise jaws also help to reduce burrs left on the material and are ideal for bundle cutting. Holding the work piece on both sides of the blade reduces blade vibration, providing more accurate cuts and longer blade life.
Out-of-Square Detector
Assures that you are always cutting within your predetermined tolerances. This feature will shut the machine off automatically should machine begin cutting outside of those parameters
LED Work Light
Positioned directly over the work area to provide better illumination of the cutting area, the work light can be turned on and off independently from the operator's control panel.
Zero Point Trim
Provides automatic detection of front workpiece to eliminate the need for a reference cut saving time and material.
Table Height
29-1/2"
Automatic Chip Conveyor
High Efficiency Transmission
Flushing Hose
HMI/PLC Controls
Machine Weight
15,400 lbs.
DEAD ROLLER TABLE (2 METER)
Heavy Duty, free-standing roller table for material handling either in-feed or discharge.