Vertical Tilt-Frame Saw

800 Series Manual Vertical Tilt-Frame Band Saw


  • Semi-Automatic
  • Heavy-Duty
  • Hydraulic
  • Metal Cutting
  • High-Speed Bandsaw
  • ± 60 Degree Miter

Get More Info


Download Brochure and Spec Sheets

Capacity: Nominal
31.25" x 37.5", 31.25" Round
Capacity: 45° Right
31.25" x 25.5", 25.5" Round
Capacity: 45° Left
31.25" x 24", 24.75" Round
Capacity: 60° Right
31.25" x 17.5", 17.5" Round
Capacity: 60° Left
31.25" x 15.75", 16" Round
Blade Drive
Electric with sensor-less vector control for smooth acceleration and full torque.
Speed Range
Infinitely variable: 60 to 400 FPM, 15 H.P. Standard. Blade speed can be automatically set when material is selected.
Tilting Column
For miter cutting up to 60° left and right of vertical. Variable speed, inverter driven, electronic tilt- Includes encoder feedback and touch screen display & control, for precision miter positioning. Electrically powered, chain driven, with encoder feedback and Amada Marvel PC3 controller.
Touch Screen Control
Blade speed, feed pressure and angles are selected using the convenient, operator friendly touch screen control.
3° Canted Column or Non-Canted Column
Standard 3° forward approach angle for increased efficiency in cutting of structural materials.
Feed Force
Direct Force Sensing Electric Ball Screw Feed 0 - 350 lbs.; column travels on recirculating linear ball ways. Feed pressure can be automatically set when material is selected.
Jammed Blade Protection
Automatically senses resistance as the column returns and stops to prevent blade damage.
Blade
25' Long x 2" Wide, .063". One Welded-Edge Band is furnished with each machine as part of standard start-up supplies.
Blade Guides
Rotating Easy Load Combination Carbide and Ball Bearing Roller guides with self tensioning design.
Blade Tension
Hydraulically controlled, 32,000 psi. max. Machine equipped automatic blade break/blade stall shut-off switch.
Upper Blade Guide Arm
Hydraulically positioned and locking, controlled by selector button on the touch screen.
Vises
Hydraulic, full stroking with 12" High x 20" Wide 60° faceplates. Optional variable vise pressure available as well as an optional second machine vise.
Coolant System
Built-in with Flood system, available with Drop Lubrication system, including chip pan with manual hand crank type chip conveyor. A Flushing hose is included to wash away chips from hard to reach places reducing clean-up time.
Work-Rest Rollers
Two turned ball bearing rollers, one on each side of the machine bed.
Standard Machine Color
Machine Tool Gray.
Standard Left-to-Right Work Entry
Opposite Hand or Right-to-Left work entry available.
Table Height
52"
Motors
Main Drive: 15 H.P. 1800 RPM, Coolant Pump: 1/2 H.P., Hydraulic Pump: 5 H.P. 1800 RPM
Controls
IEC fused disconnect switch and magnetic motor starters with overload and low-voltage protection. Power supply provides low voltage control to all push buttons at operator's control panel and machine lighting circuits. PLC control and drives mounted in moisture tight compartment with vibration isolation mountings. Electrical Equipment conforms to National Electrical Code NFPA 79. The Electrical Control Panel is U.L. Labeled.
Opposite Hand Work Entry
Right-to-Left instead of Left-to-Right normally furnished.
Powered Chip Conveyor
Automatic motorized “scraper type” chip conveyor in place of standard manual chip conveyor. Includes drive motor with gear reduction and automatic shut off.
Variable Vise Pressure Control
Enables hydraulic pressure of work holding vises to be adjusted as required. Includes hydraulic pressure gauge and operator control.
SUPPLEMENTARY EQUIPMENT UPON REQUEST.
DEAD ROLLER (NON-POWERED) ROLLER TABLE SECTIONS
First Section Dead Roller Table, 10’ 0” Long
Six Ball Bearing Idler Rollers, 3.5” diameter, spaced on 30”  centers; 6 Flush Plates, and Coolant Pan.
First Section Dead Roller Table, 5’ 0” Long
Three Ball Bearing Idler Rollers, 3.5” diameter, spaced on 20” centers; (3 Flush Plates), and Coolant Pan.
Extension Dead Roller Table 5’ 0” Long
Three Ball Bearing rollers, Coolant Pan, no Flush Plates.
Extension Dead Roller Table, 10’ 0” Long
Six Ball Bearing rollers, Coolant Pan, no Flush Plates.
LIVE (POWER DRIVEN) ROLLER-TABLE SECTIONS
Automatic Power Roller Extension
Provides power to operate in-feed/discharge roller tables beyond thirty feet in length.
Live Roller Table 5’ ’0” Long
Three powered Ball Bearing rollers, 4.5” diameter mounted in cast iron pillow blocks on 30” centers, Coolant Pan, no Flush Plates.
Extension Live Roller Table 10’ 0” Long
Six powered Ball Bearing rollers, 4.5”  diameter, mounted in cast iron pillow blocks on 30” centers, Coolant Pan, no Flush Plates.